Free Shipping
Fast Delivery
Great Prices
Rush Production Available

Calculate spine width

The spine width is the width of the spine of your hardcover. You need that figure to lay out your cover: the spine sits between the front board and the back board, and if the measurement is off, the spine text ends up crooked or partly on the board. Below you calculate the spine width with the same formula we use in production.

Pages, not sheets. One sheet is 2 pages.
Spine width 
Thickness per page
 
Book block
 
Board
 
Cover trim size
 
Cover sheet with 15 mm turn-in
 
Supply inner pages at
 

Calculated with the formula from the Printforce Cover Size Calculator: paper weight × bulk ÷ 2000 × number of pages, plus 2 × 2.25 mm board. We always check the spine width once more before we print.

How the calculation works

The spine consists of the book block plus twice the board of the covers. The book block is the thickness of all the pages together. That thickness depends on two things: the weight of the paper and the bulk of the paper.

  1. Thickness per page = paper weight × bulk ÷ 2000
  2. Book block = thickness per page × number of pages
  3. Thread sewn: book block + 10 percent
  4. Spine width = book block + 2 × 2.25 mm board
  5. Rounded spine: divide the result by 0.91

An example. A novel of 200 pages on white novel paper of 90 grams with a bulk of 1.95. The thickness per page is 90 × 1.95 ÷ 2000 = 0.08775 mm. The book block is 200 × 0.08775 = 17.55 mm. Add 2 × 2.25 mm of board and the spine width is 22.05 mm.

Why bulk matters more than weight

Two papers of 90 grams each can differ considerably in thickness. The bulk, also called volume, tells you how airy the paper is. Novel paper of 90 grams has a bulk of 1.95 and is therefore almost twice as thick as coated silk of 90 grams with a bulk of 0.92. Over 300 pages that is a difference of more than 15 mm in the spine. Working from the grammage alone always goes wrong.

Bulk per paper type

These are the bulk figures we work with. They come from the paper mill specifications.

Paper type Weight Bulk
Cream novel paper 70 g 1.74 or 1.94
Cream novel paper 80 g 1.93
White novel paper 80 and 90 g 1.95
Woodfree offset white 80 and 90 g 1.34
Woodfree offset white 100 and 120 g 1.30
Biotop cream 80 to 120 g 1.30
Matt coated 70 to 130 g 0.96
Matt coated 150 g 1.00
Silk coated 100 to 150 g 0.92
Silk coated 170 g 0.93
Gloss coated 90 to 170 g 0.79 to 0.82

Not sure which paper suits your book? Then read choosing paper weight first.

Thread sewn adds ten percent

In a sewn binding the sections are sewn together with thread. That thread sits between the sections and makes the book block thicker. We add 10 percent to the book block for it. Please note: for a print run of one copy we do not sew. Use the glued binding in that case, otherwise your spine comes out too wide.

Square or rounded spine

With a rounded spine the book block is rounded off. Measured over the outside, the spine then becomes longer than with a flat spine. We divide the spine width by 0.91 for that, the cosine of the rounding angle of 24 degrees. A spine of 22.05 mm becomes 24.23 mm.

From spine width to cover sheet

The spine width alone does not get you there. A hardcover cover is larger than the book block, because the board overhangs and the paper is folded around the board. The calculator works that out for you:

  • At the head, the tail and the fore edge the board is 3 mm larger than the inner pages.
  • On the spine side, 7 mm of the page width disappears into the hinge groove.
  • Between board and spine there is a hinge of 8 mm on both sides.
  • All around comes 15 mm of turn-in: the paper that is folded around the edge of the board.

The line cover trim size is the size of the cover as it sits around the book. The line cover sheet with 15 mm turn-in is the size you supply your PDF at. You can read more about how the cover is built up at cover paper.

Common mistakes

  • Counting sheets instead of pages. One sheet of paper is two pages.
  • Calculating with the cover paper instead of the inner paper. Only the inner pages determine the book block.
  • Forgetting the endpapers. We count the endpapers separately, they are not part of your page count.
  • Putting the spine text right up against the spine fold. Keep at least 0.6 mm of air on both sides.
  • Reusing an old spine width after adding or removing pages.

We always check the spine afterwards

The result above is the calculated value. Paper has a production tolerance, so we measure the actual block thickness before we print the cover. If it differs, we adjust the cover and let you know. In doubt about your file or your measurements? Get in touch and we will look at it with you.